Equipment features
Moving platform with rotary and lifting table
Three motions make this machine different from a plain flat bed: the platform feeds the work, the table lifts to the focus height, and a rotary attachment turns cylindrical parts under the head. That is what allows a workshop to cut flat acrylic and engrave a coated cylinder without moving to a second machine.
Moving platform feeding
- The work platform advances the material into the cutting area.
- Loading and cutting positions are separated, which shortens the handling step.
Rotary attachment
- Cylindrical parts are clamped and turned under the head for engraving.
- Clamp diameter range 20–300 mm.
Automatic focusing
- Focus distance is set by the machine rather than by hand.
- Consistent results when switching between flat and round work.
Automatic up-down table
- Table height adjusts over a 200–800 mm lifting range.
- Thick workpieces still sit at the correct focus position.
Cutting and engraving in one machine
- The same head cuts outlines and engraves surface detail.
- Suited to workshops producing both flat parts and round products.
CO₂ tube 70–130 W
- Peak power 70 / 80 / 100 / 130 W; 10.6 µm wavelength.
- Working area 1 200×800 mm for the flat-bed mode.
Applications
Flat sheet and cylindrical work
Specified where the product range includes round parts as well as flat ones, and where a second rotary machine would sit idle most of the time.
Materials
Acrylic, double-colour engraving board, plywood, MDF, rubber, plastics, cloth, leather, bamboo and wooden products and other non-metal materials. The rotary attachment applies to round parts in the clamp range; longer or heavier cylinders are reviewed before quotation.
Technical specifications
Technical Specifications
| Peak Laser Power | 70W/80W/100W/130W |
|---|---|
| Wavelength | 10.6um |
| Lifting Range | 200-800MM |
| Rotary Clamp Diameter | 20-300MM |
| Cutting Speed | 0-64000mm/min |
| Local Length | 38.1,50.8,63.5,76.2,101.6MM |
| Location Precision | 0.015mm |
| Min.Line Width | 0.15-0.3mm |
| Cooling Mode | Water Cooling and Protection System |
| Graphic Formats Supported | PLT,DST,AI,DXF,BMP,JPG,CAD,CDR,DWG |
| Controlling System | DSP High Speed Controller |
| Operating temperature | 0℃-40℃ |
| Humidity | 5% to 85% (No Condensed ) |
| Gross Power | <1250W |
| Power source | AC110V/220V± 10%, 50/60HZ |
| Processing Area | 1200*800mm |
| Working Environment | Clean, Free of Dust |
Values describe the standard configuration. Rotary work depends on the clamp range and the diameter of the part, so a sample cylinder is tested before the configuration is fixed.
Three motions, one setup
Platform feed, table lift and rotary turning are set up as one job. For flat work the rotary unit is out of the path and the platform advances the sheet; for round work the part is clamped, the table lifts to the right height, and the controller rotates it while engraving. Send the part drawing — flat, round or both — and the configuration is planned around it.
Configuration & support
Matching the machine to your work
Peak power70 / 80 / 100 / 130 W by configuration.
RotaryClamp diameter 20–300 mm, matched to the part.
Lifting range200–800 mm automatic up-down table.
Part testFlat and round samples engraved before quotation.
Request a quote
Send the round and flat parts
Share the diameter and length of the cylindrical part, plus the flat work you also need. HODA confirms the clamp range, lifting height and quotation for the CO₂ laser cutting machine with moving platform.
Product / model: CO₂ Laser Cutting Machine with Moving Platform
